Types of Water Contaminants Found In Arizona’s Water

types of water contaminants

Arizona is the fourth driest state in the nation and water needs to be conserved and used efficiently. The hard water climate in Phoenix means that water quality is a constant challenge for the city’s residents. Still, they have made significant strides in maintaining the water quality that is made available. Wells are the most common drinking water source in Arizona because there are few rivers or lakes for surface-water supply. Wells may be drilled into bedrock or into unconsolidated material that yields groundwater. In either case, many types of common contaminants in water from the outside environment may become mixed into the potable water supply if proper well construction procedures are not followed.  Read on to learn about some common water contaminants in Arizona’s water supply, as well as some ways you can determine if any of these agents has contaminated your well. Sulfate  Sulfate is one of the most common types of water contaminants and is a naturally occurring element found in soil, rocks, water and air. It is often used commercially to increase the brightness of detergents and bleaches. However, high levels can give water an unpleasant odor or taste and cause corrosion of plumbing fixtures such as hot water heaters. Iron  The presence of iron can result in rust on fixtures and plumbing pipes if not properly treated. The presence of iron may also result in discoloration of the water, leading to the well being identified as a potentially serious health hazard.  Manganese  Manganese can enter your water supply through several ways, including well drilling equipment, groundwater flow or a variety of natural soil sources such as volcanic ash. Long-term exposure to high levels has been linked to nervous disorders, and black manganese, a special form of the element, is known to cause cancer in animals and humans. Radon  Radon is a naturally occurring radioactive gas found in the soil. It is known to cause lung cancer. The Arizona Department of Environmental Quality requires that any water system serving over 100 people must test for radon annually. However, wells serving smaller populations may overlook this hazardous contaminant. Iron Bacteria  These bacteria love to grow on iron and manganese, which means that they may accompany high iron levels in your water supply. A significant presence of these microbes can cause discolored or smelly water if not properly handled and may pose a potential health hazard as well. Copper  Copper is an essential trace mineral for living organisms and occurs naturally in groundwater supplies throughout the world. The presence of excess copper in water reservoirs may result in discolored water if not handled properly. Nitrate  Some wells – especially those dug into hard-rock formations or high rainfall areas – may contain high levels of organic contaminants in water, including problematic nitrate levels, even if the well doesn’t contain measurable nitrate levels. Water with nitrate does not pose a danger to health. However, nitrate can combine with certain bacteria to form nitrogen dioxide gas, which can cause various illnesses, including nausea, dizziness, and headaches. Arsenic  Arsenic is a carcinogen and a naturally occurring element found in soil, rocks, water and air. Long-term exposure to high levels may result in skin or gastrointestinal cancers. Therefore, the EPA has set limits on arsenic concentrations in drinking water, and arsenic levels in Arizona drinking water must meet or exceed the EPA’s standard. Radium  Radium occurs naturally in soil, rock, and groundwater. It is also found at sites where uranium is used to fuel nuclear weapons production and nuclear reactors. Just like arsenic, the EPA set limits on radium concentrations in drinking water, Arizona’s drinking water needs to meet the standard set by them to be considered potable. Fluoride  Fluoride is necessary for normal body functions and is usually left present in drinking water for health benefits. However, water with high fluoride levels may be irritating to the skin, eyes, and digestive tract. High levels may also cause bone defects, including osteoporosis (bones become weak and brittle). How to tell if your water is contaminated 1. If your water supply is from a well and the water does not have a strong chlorine odor or taste, it probably contains high iron levels. Rust may appear in fixtures or on plumbing pipes. 2. If your water supply is from a well and the water has a noticeable blue-green tint, it probably contains high levels of manganese. 3. If you have recently dug or installed a septic tank on your property, there is a possibility that the area has become contaminated with radon gas as the groundwater table rises to meet the new drain field. Have the soil tested for radon gas at least every three years afterward. 4. If your water has a chlorine odor or taste but it does not contain rust or iron discoloration, it probably contains high levels of copper. Other sources include plumbing pipes and hot water heaters. 5. If your water has a sulfur odor or taste, it probably contains high levels of sulfate. Other sources include sulfur-based fertilizers and plumbing fixtures such as hot water heaters. 6. If you have lower than normal chlorine levels in your finished water, it may contain high levels of radon. Radon is a radioactive gas that may be caused by decaying uranium in the soil and accumulate in your well. 7. If your water has a very salty taste or affects the taste of food when used for cooking, it probably contains high salt levels. Natural sources of sodium chloride can be seawater intrusion, salt transported with groundwater or saline soils, or sea spray from the ocean. Other sources are salt-based fertilizers and groundwater from saline aquifers. 8. If your water has a very sweet taste, it probably contains high levels of nitrate. Nitrate is found naturally in ground and surface water, and fertilizer runoff from agriculture can cause elevated nitrate concentrations. Nitrates do not pose health problems when used for drinking but may lead to illness if consumed in large

Water Filter vs. Purifiers: Is There A Difference?

Water Filter vs. Purifiers

We all know the importance of clean water. Whether we are consuming it or using it for cleaning, dirty water is not helpful and can make us really unwell. There are a range of methods to ensure you have clean water to conduct your daily activities. The problem is that it can be confusing to determine the difference between these methods and the one that is best suited for your situation. Water filters and water purifiers are both commonly used to treat water, but what is the difference between the two? We’ve done a comprehensive rundown of water filters vs water purifier so that you have a better understanding of what each one does. Water Filters vs. Purifiers: Exploring Each Water Filters First up in our water filter vs purifier exploration, let’s take a look at filters. There is a range of different water filters that can be used to clean your supply. Regardless of the type, they essentially serve the same purpose. That is, they block the contaminants in your water (and there are many water contaminants in cities like Phoenix) so that your water flows out of your taps but the dirt and other impurities do not. Let’s take a look at each type of filter so you can determine the one that best suits your requirements. Whole House Filters As their name would suggest, whole house filters treat water for every faucet in your home. It is installed at the main water line so that it can filter water on its way through to your home. Typically, this type of water contains a sediment filter that separates things like dirt, silt, and rust.  After this, it runs through another filter (copper-zinc and mineral stone) to remove chlorine and heavy metals that are soluble in water. This part of the process also usually treats the water for algae growth and creates an environment where the existence of bacteria is inhibited.  The water is then processed through a carbon filter that minimizes the presence of pesticides, herbicides, and chemical compounds in the liquid.  House filters are usually designed so that they can be customized to suit your home and specific requirements. You might live in an area where it is practical to have a UV filter to remove bacteria and viruses from your water. In other locations, a water conditioner might be more important to prevent a buildup of scale in your pipes. Take a look at our website for the best water filter for Phoenix, Arizona.  Water filters are highly adaptable so you will be able to find a solution that is most effective for your local water.  Point-of-Use Filters Having clean water is particularly important when it comes to consumption. This is why some people opt to install specific drinking filters that make sure their water is fresh and clean for drinking. There is a range of designs you need to make when it comes to drinking filters. Some come as an additional tap on your bench while others are units that are positioned under the sink. Regardless of the design, most work in the same way. Drinking filters clean water by using activated carbon as well as ion exchange. This means that the filter attracts and collects contaminants such as heavy metals, chlorine, and pharmaceuticals, preventing them from flowing through your tap.  Drinking filters are highly effective at removing these potentially harmful compounds. While they do have the effect of removing minerals as well, this isn’t as severe an issue as you might think. Your body gets most of its vital minerals from your diet, which is why removing them from your drinking water is unlikely to cause adverse health effects unless you have a condition requiring micro-management of your mineral intake. Shower Filters Alternatively, it is possible to get a filter for your shower. These usually come in designs that can easily attach to a standard showerhead or replace it altogether.  If you live in a location that has ‘hard’ water, this may be a worthwhile option. Hard water makes it difficult to lather soap so it can be difficult to wash your hair and body properly. Shower filters are also good for water sources that are high in chlorine or other chemicals. These types of substances can dry out skin and hair, impacting their health and appearance. Water Purifier Water purifiers are highly effective in treating water. In general, they are able to do the role of a filter and more. They are generally defined as systems that remove upwards of 95% of contaminants from your drinking water. These systems also often remove living organisms (like bacteria and protozoa), which filters don’t necessarily get rid of. Purifiers come in a variety of designs but typically utilize one of the following technologies: Reverse osmosis Distillation Check out this post for a comparison of the two. Reverse osmosis This type of water purifier works very much like a filter. It uses a semi-permeable membrane (kind of like egg whites) to separate contaminants from the water. What happens is that the clean water passes through, while larger contaminant particles get stuck and therefore are removed from the water. Reverse osmosis is highly effective. It can purge as much as 99% of contaminants from your water. Distillation Distillation works in a different manner. It separates water from contaminants by boiling the water. The clean water is turned into steam, which enables it to be collected while the contaminant particles (including bacteria) remain behind.  One concern people have with consuming purified water is that it is more acidic than normal water. Check out this post to learn more about why this is and whether you should actually be concerned. Water Filter vs Water Purifier: Which is Better? Many people have opinions on these two methods, with people being particularly interested in the UV water purifier vs filter debate. After a thorough investigation into each method, it’s time to offer our view. The truth is, filters and purifiers have

How To Make Distilled Water: 6 Easy Steps

How To Make Distilled Water

Distilled water is useful for a variety of applications. If you use it on a regular basis, though, distilled water can prove costly and inconvenient to have to buy constantly. Please refer to our several service areas, including Chandler, Buckeye and Scottsdale, for your plumbing and HVAC needs. In this post, we’ll show you how to make distilled water easily. We’ll also give you some more detailed guidance on what you should use this water for. While you are here, also check out Maricopa county air quality report. How to Make Distilled Water: What You Should Know First As we mentioned in this article, distilled water is not ideal for drinking, particularly if you’re making it yourself. The distillation process may kill microbes but it leaves chemicals like heavy metals behind. Without further processing, you’ll end up drinking the same chemicals you were probably trying to avoid. Additionally, distilled water pulls minerals from any material it comes into contact with. In other words, if you store your homemade distilled water in a plastic jug for extended periods of time, you’ll find that chemicals begin to leak into it. This exacerbates the drinkability issue. If you’re looking to purify water for drinking purposes, you’ll find whole house water filters to be much more effective. You can also check out the Pro Health System which is a seven-stage whole house water filtration system that is perfect for Phoenix, AZ residents. As for distilled water, you’ll find it very helpful for things such as: How to Make Distilled Water Easily The Process Before we get into the steps, let’s briefly explain what happens during the distillation process. While many people mistakenly believe that distillation simply involves boiling your water, it’s a bit more complicated than that. Distillation is a chemical process through which you boil water into a vapor and then condense it back into a liquid. It’s good for a lot more than just water, too; for example, alcohol manufacturers use distillation to extract liquor. Primitive forms of distillation have existed for centuries; Aristotle once marveled at how it could transform seawater into something purer. Today, distillation plants are large operations relying on different forms of the chemical process, including: The technique you’ll likely be using at home is steam distillation. We’ll share a few other methods as well, though. How to Make Distilled Water at Home Using Steam Here’s the first and arguably the simplest method. The pot should be stainless steel and capable of holding roughly five gallons of water. It should also have a lid. This bowl is what’s going to collect the distilled water so make sure it’s fairly large in relation to the amount of water in the pot. The water doesn’t need to reach boiling temperatures although that’s fine if it does. As the water inside the pot gets heated, droplets (condensation) will form on the lid. The ice cubes (or other cold material) on the other side of the lid will help with this process. The distilled water will fall back down into your bowl. Once this process is complete, you’ll need to find a suitable container to store your distilled water in. Dishwasher-safe glass is ideal. Only use plastic if you plan on storing the distilled water for a limited period of time; remember, chemicals will easily leak from the plastic into your water if you’re not careful. Method #2 The above method works great if you don’t mind leaving your distilled water to cool before you use it. If, however, you need to use the water immediately after distilling it, here’s what you do.  Instead of placing a bowl in the pot to catch the condensation, you’ll want to funnel it outside to a separate container.  Place a large funnel over the pot and then connect tubing to your separate bottle. You’ll need to place the separate bottle on a lower plane than the pot since you’re relying on gravity to pull it through the tubing. If you’re looking for how to make distilled water from tap water, one of these two methods is your best bet. How to Make Your Own Distilled Water Using Natural Precipitation Did you know that precipitation is a natural form of distillation? Think about it: water rises from oceans and lakes before condensing into droplets and falling back to earth in the form of precipitation. In areas with minimal pollution, this precipitation is about as pure as water can get. In smog-ridden cities, however, pollution contaminates the droplets as they fall back to earth. As such, you’d likely want to process the water further. Here’s how you do it. You’re probably not going to want to drink this water unless you’re in a dire situation. This is still a good method to have in your back pocket if you need distilled water regularly and live in an area where it rains a lot. How to Make Distilled Water for Your Humidifier Using a Kit While the steam method is great and easy, it does have some downsides. For one, you’ll need to use electricity. This isn’t a huge deal if you only need distilled water once in a while. If, however, you need it on a regular basis, you may find it more effective to purchase a distillation kit. These kits come in the form of electric devices that more or less handle everything for you. YOu can find them from $100 to $1,000 or more. Alternatives to Distillation As mentioned earlier, distillation isn’t ideal for every application. If you need something more versatile, you might prefer a point-of-entry water filter like the Big Blue, which we wrote about here. If point of entry filters aren’t an option, you can also buy a reverse osmosis system that purifies water at a single faucet. Advantages of a reverse osmosis system over distillation include: The benefits of reverse osmosis water make it an easy and viable alternative to distillation. So If you’re looking for a worthy alternative, reverse

Is Reverse Osmosis Water Acidic? How To Test Yours

Is Reverse Osmosis Water Acidic

Reverse osmosis systems are among the most popular residential water filters. But is reverse osmosis water acidic? Are the masses mistaken in trusting them? Keep reading for the answers to these and more questions. Is Reverse Osmosis Water Acidic or Alkaline? Put simply, yes, reverse osmosis water is acidic. While the pH level of tap water in Arizona ranges from 7.1 to 8.4, reverse osmosis water hovers around the 6.5 mark, representing greater acidity. Is this going to have an impact on your health? Probably not. The Environmental Protection Agency states that water with a pH of 6.5 is perfectly safe to drink.  This isn’t exclusive to reverse osmosis filters, by the way. Also popular are whole house filters in Phoenix, which will increase your water’s acidity as well. As you’ll see shortly, this all comes down to what these filters remove. What is Acidity, Anyway? Acidity is the opposite of alkalinity. Higher numbers on the pH scale represent greater alkalinity. The scale works logarithmically, with each number representing a 10-fold increase in alkalinity or acidity compared to the previous digit. That would make reverse osmosis water with a pH of 6.5 10 times more acidic than unfiltered water with a pH of 7.5. Before you panic and start telling all your friends to rip out their reverse osmosis systems, though, it’s worth taking a look at the pH levels of other substances: In other words, you consume liquids far more acidic than alkaline water on a daily basis. Why is Reverse Osmosis Water Acidic? Warning: This gets a bit nerdy. According to Scientific American, acidic liquids easily transfer hydrogen ions into a solution. Weak acids (like reverse osmosis water) do this very easily. Alkaline liquids work in the opposite manner. The more alkaline something is (i.e. the higher it is on the pH scale), the easier it will accept hydrogen ions. So why is reverse osmosis water acidic? Well, it’s all thanks to the filtration of alkaline mineral atoms. As we discussed in this post, reverse osmosis filters remove minerals like calcium and magnesium from your water. Should you worry about the removal of these minerals? After all, calcium and magnesium are good for you, right? While it is important that you ingest your required daily intake of those minerals, you’re not going to achieve that with water. Your body gets the bulk of its calcium and magnesium from your diet, which is why soft water is considered safe to drink, as we discussed in this guide. Would Reverse Osmosis Water Impact an Alkaline Diet? Given reverse osmosis water’s acidity, one might question whether it would counteract something like an alkaline diet. The idea behind alkaline diets (as promoted by celebrities like Victoria Beckham) is that creating an “alkaline environment” in your blood can improve your overall health. While the alkaline diet does have some benefits, according to Dr. Melinda Ratini writing for WebMD, this rationale is flawed. Nothing you eat or drink (not even reverse osmosis water) is going to have a major impact on your blood’s pH level. Your body regulates this level just fine on its own. In other words, drinking reverse osmosis water isn’t going to “throw your blood off balance” or anything of that sort.  This isn’t to say an alkaline diet is totally useless, though; your health will improve as a result of the foods you eat while on this diet. It just doesn’t happen in the way you’d expect it to. In fact, the chemicals you would ingest if you didn’t have a reverse osmosis filter (or some other type of system) would impact your health much more severely than any minor acidity would. This is why reverse osmosis systems in Phoenix are so popular. Compounds like lead, arsenic, and chlorine (all of which are prevalent in America’s drinking water, as we discussed here) will harm you over the long haul. Acidity is just a byproduct of removing these minerals from your drinking water. How to Test Your Water’s Acidity While you should know by now that reverse osmosis water’s acidity shouldn’t be a major concern, you might still want to see exactly where yours falls on the spectrum. You can also check out our article about the ideal water pH level for your home as a reference. There are three reliable methods for doing this. Let’s take a look at them. pH Strips When you soak a pH test strip in any given liquid (your reverse osmosis water, in this case), it will change color based on where it falls on the acidity-alkalinity spectrum. Your best bet would be to buy a strip designed to test within the 5.5-8.5 range, in which your reverse osmosis water will likely fall. If you get a strip that tests too broadly, you may find it hard to distinguish between the hues that would give you an accurate idea of your water’s measurement. Litmus Paper Litmus paper works similarly to a pH strip, only with less accuracy. When you soak litmus paper, it will simply turn one of two colors based on whether it’s acidic or alkaline. Keep in mind that reverse osmosis water is a relatively weak acid. Depending on what type of litmus paper you choose, your water may not even show up as acidic. Local Testing Facility What a lot of people don’t realize is that many American cities have local water testing services run out of universities or local government facilities. As we discussed in our article on hard water testing, you can send your water into these facilities and have it analyzed. The results you’ll get from these sources will be much more accurate than the approximations you’d find with pH strips and litmus paper. Bonus Method: Red Cabbage You can also perform an approximate test of your water’s pH level using — believe it or not — a piece of red cabbage. Red cabbage contains a pigment that will change color based on the pH level of whatever

Big Blue Water Filter Housing: Everything You Need To Know

Big Blue Water Filter Housing

The Big Blue water filter’s housing is based on a deceptively simple and ingenious design. Throughout our more than 30 years of experience in the HVAC and water filtration business, we’ve installed and serviced countless of these units. That’s why we’ve put together this guide to help answer some of the common questions we receive about the Big Blue filter. Let’s dive in! But before that, check out these fun facts about Scottsdale. Big Blue Water Filter Housing: The Basics The Big Blue water filter is a point-of-entry (POE) system, meaning the unit filters your water supply before it gets to your various fixtures. It’s a very cost-effective method of filtration because you only need to worry about maintaining one unit as opposed to several for all the different faucets and fixtures in your home. Now, the term “Big Blue” has become to water filters what the term “Kleenex” is to tissues. That is to say, there are many brands that produce similar-looking filters that inexperienced consumers (and even some technicians) refer to as “Big Blue.” In actuality, the term “Big Blue” is registered to a company called Pentair. Unlike some of the imitation “Big Blue” filters out there, Pentair’s products are built remarkably well and are very effective. They get their name from the characteristic blue housing that Pentair designed. About Pentair Within the HVAC and water filtration industry, Pentair is a behemoth. They own many brands, with Pentek being the one under which their Big Blue filters fall. Pentek specializes in residential water filtration systems, whereas Pentair’s other brands cover systems for everything from agriculture to commercial and industrial applications. What’s Special About The Big Blue Water Filter Housing? Given that there are so many imitations of the Big Blue filter on the market, one might be tempted to find a cheaper version and call it a day. Here’s why that’s a bad idea. #1. Pentair is a Highly Trusted Company HVAC and water technicians have a very high view of Pentair — and for good reason. The company has been around since 1966 and is established in more than 25 countries. Pentair’s extensive expertise in all things related to water filtration means that their product designs (such as the Big Blue filter in question) are highly informed. Less-reputable companies have been known to produce lower-quality units that don’t work as efficiently as the Big Blue. #2. Serviceability The Big Blue filter is ubiquitous. Any water technician worth their salt knows how to install and service one of these units. There are even plenty of guides online (such as this one) showing you how to use the unit yourself. Plus, you can find parts for the Big Blue filter at most home hardware stores. This isn’t always the case with more obscure filters. #3. Size As its name would suggest, the Big Blue filter is larger than many other filters on the market. This allows you to use a wider array of cartridges and generally achieve greater efficiency than you would with a smaller filter. This larger size also reflects the Big Blue’s intended use as a POE filter. Smaller units are really only meant for point-of-use purposes (i.e. you’d affix them directly to your faucet as opposed to at the point of entry). How Does The Big Blue Water Filter Housing Work? The Big Blue housing contains the filter that cleans your water. It is attached to a black valve through which water enters. From there, the water makes its way down into the housing, where it passes through the cleansing cartridge before being pumped back up through the valve and to your fixtures. One of the reasons this design is popular is that the Big Blue allows you to place a variety of filters (they come in standardized sizes that we’ll explore shortly) in the unit depending on what you’re trying to remove. Big Blue Filter Housing Specifications Big Blue filter housing specifications vary. They accept cartridges that are 4-½“ in diameter and either 10” or 20” in length. The unit’s high-flow polypropylene (HFPP) top comes with the following inlet port dimensions: The latter port allows for a larger amount of liquid to flow through the unit. With Big Blue housings, users can choose between units with or without pressure relief buttons. User Servicing: How Often To Change Big Blue Water Filter The filter housing itself can last for a very long time; Pentek only recommends you replace it after 4-5 years of use. The cartridge should be replaced roughly every 100,000 gallons. It depends on several factors, though, including what cartridge you’re using and the water quality in your area. This cost is truly negligible when you consider the alternatives to water filtration, such as buying bottled water instead. The fact that these units last 10 years is also pretty remarkable. Every time you close a faucet in your home, a water hammer occurs. In a nutshell, water flows through your pipes (and your water filter) at a relatively fast rate. When you shut off the faucet, this flow suddenly stops. The energy gets dissipated to a variety of appliances, including your water filter. Inferior filters start to crack and lose their structural integrity much sooner than 10 years as a result of this force (water heaters may smell and shorten it’s life expectancy as a result). How To Change The Filter Important: Use The Big Blue Filter Wrench The Big Blue filter wrench (which comes with the unit) fits nearly around the housing and allows you to evenly unscrew the unit as opposed to applying uneven twisting pressure with your hands, which may damage the unit over time. After you loosen the housing with the wrench, you’ll see the Big Blue filter o-ring. Hand onto this; it’s an important gasket that you’ll want to put back in its spot after you change the cartridge. Changing the cartridge itself is relatively simple. Just pull it out and pop a new one in! Then, replace

Water Filter vs. Bottled Water: How To Save Hundreds Of Dollars

Water Filter vs. Bottled Water

The question of ‘water filter vs. bottled water’ is one we hear quite often at American Home Water and Air. While cost is among the chief concerns people raise related to this topic, it also has major implications for your family’s health. In this post, we’ll explore the economics and health impacts of relying on either bottled water or filtered tap water for your family’s drinking supply. Water Filter vs. Bottled Water: Economics Cost of Bottled Water vs. Tap Water Americans spend $16 billion per year on bottled water. Without exploring the purity of bottled water just yet, let’s explore whether it makes economic sense. According to Business Insider, American consumers spend an average of $1.22 per gallon of bottled water. That’s 300x more than a gallon of tap water costs you. It gets worse, though. Those initial figures from Business Insider only apply if you’re buying bottled water in bulk. The bottled water vs. tap water cost discrepancy becomes even more egregious when you consider that nearly two-thirds of water bottle sales in America are for single units, which come at a cost of $7.50 per gallon. That’s nearly 2000x more than a gallon of tap water costs you. Of course, this assumes you’re just drinking the water straight from the tap. Whole house filtration systems come at a cost, so let’s explore those economics next. Filtered vs. Bottled Water: Cost Comparison Filtration systems like those relying on reverse osmosis (learn about what that is and why it’s so popular here) carry an upfront cost. Since our reverse osmosis systems in Phoenix start at $350, we’ll reference that. However, the cost may differ when sizing for water heaters and other filtration systems. Reverse osmosis systems in general also consume about two gallons of water for every one gallon they produce. One article in AZ Central quoted a cost of $0.007 per gallon of tap water as being at the upper end of what Phoenix metropolitan-area residents deal with. So, with a reverse osmosis system, that works out to an additional cost of $0.014 per gallon you drink on a regular basis. In other words, even assuming the worst at every turn, it’s quite a negligible cost. Now that we have an understanding of costs for bottled water, unfiltered tap water, and filtered tap water, let’s tie it all together. Cost of Bottled Water vs. Tap & Filtered Water: Tying It All Together Americans drink an average of 58 gallons of water annually according to The Atlantic. If you buy bottled water in bulk, that will cost you roughly $70.76 per person in your household annually. If you buy single bottles (as most Americans do), you are looking at a cost of $435 per person annually. Unfiltered tap water would cost you (according to worst-case scenario figures in Arizona) a whopping 40 cents per person, per year. Tap water filtered through reverse osmosis, meanwhile, would cost you $1.21 per person, per year, assuming the system you buy uses two gallons of water for every one gallon it produces. Of course, with reverse osmosis systems, you have the upfront installation costs — but those are one-time fees that vanish by the second year. In other words, reverse osmosis very quickly becomes the most economically viable way to ensure pure drinking water for your family. Now that we’ve explored the bottled water vs. tap water cost question at length, let’s explore which is healthier for you: bottled water or filtered water. Filtered vs. Bottled Water: Health Impacts For decades, research has shown that bottled water isn’t as healthy as many people assume it to be. Part of the issue lies in the fact that bottled water is actually less regulated than tap water. That’s quite alarming since it’s no secret that tap water in the United States has serious contamination issues. In many cases, there’s actually no difference between well water vs. bottled water other than the fact that you are trusting manufacturers to employ good testing on the tap water before bottling it. In other words, you’re basically outsourcing the work of filtering your city’s tap water. Bottled water companies are happy to charge you a rate many orders of magnitude beyond what you’d pay for filtering your tap water yourself, with no discernible health benefits. Bottled Water vs. Water Filter: Plastic Is Dangerous, Too The plastic used to produce bottled water can harm your health, negating any benefits purification you were counting on. One study showed that these plastics are especially susceptible to leaking chemicals when you store the bottles in areas of elevated temperature. That includes hot cars, backpacks, or even your home if you live in a place like Phoenix that experiences sweltering summers. One of the most heavily-studied of these chemicals in plastic bottles is BPA. Here’s a rundown of its potential health effects. Hormone Disruption BPA mimics the hormone estrogen. This can have impacts on your developing children (such as delaying puberty), decrease your fertility, weaken your immune system, and increase your weight. Behavioral Issues Children and infants are especially susceptible to behavioral issues that can come about due to BPA’s impact on the brain. Possible Increased Cancer Risk Animal studies have shown that BPA exposure can increase the risk of cancer in animals. Potential Heart Issues In clinical studies, patients with elevated levels of BPA in their bodies were observed to have the highest rates of cardiovascular issues. Researchers aren’t certain whether this is directly related to BPA, however, or whether patients with elevated BPA levels are simply more likely to have other risk factors as well. Keep in mind that BPA is just one of the chemicals in plastic bottles. Researchers are constantly testing others and their results may prove even further that plastic water bottles are detrimental to human health. Bottled Water vs. Water Filter: Environmental Impacts Reverse osmosis systems do not use electricity. They rely on your home’s water pressure to force your tap water supply through a series of fine

Reverse Osmosis vs. Distilled Water: Read This Before You Decide!

Reverse Osmosis vs. Distilled Water

The topic of reverse osmosis vs distilled water is one we come across fairly often at American Home Water and Air. There are many substantial differences between the two, however, that may influence which one you decide to use in your home. In this post, we’ll take a look at the science behind distillation and the reverse osmosis process to establish a deep understanding of both. Reverse Osmosis vs. Distilled Water: The Basics Reverse osmosis is a filtration process that forces your water through a series of fine membranes. Our reverse osmosis systems in Phoenix consist of four or five-stage membranes that ensure almost no sediment or contaminants enter your family’s drinking water. The main reason people install reverse osmosis systems in their homes is to provide clean drinking water for their families. Distillation, on the other hand, is the process of boiling water, capturing the condensation, and allowing it to condense back into the water. After the water is distilled, impurities will be separated. Note that distillation is different from the process many municipalities recommend for purifying your water. Simply boiling the water will kill bacteria and microbes in it but it will not remove chemicals and other impurities like minerals. Both distillation and reverse osmosis provide clean drinking water but only one (reverse osmosis) is practical for residential purposes. Is Reverse Osmosis Water Distilled? Now, you may be scratching your head. After all, both processes remove impurities and theoretically leave you with ‘pure’ water. So is reverse osmosis water distilled, and vice versa? Nope. When it comes to Phoenix drinking water, both filtration and reverse osmosis methods can be used to provide clean and safe drinking water if done correctly. One similarity between the two processes is that some people claim that the water produced using either method tastes “flat” This is because both processes remove minerals. Although this may be the case for some, the main focus for Phoenix drinking water should be the safety and cleanliness of the water produced. Distillation, however, does not remove volatile chemicals like chloramines with the same effectiveness as reverse osmosis. Distilling water is a decent short-term solution (say, if you’re traveling and staying in a property that’s not yours) but reverse osmosis is the best long-term solution for pure drinking water at home. The most accurate way to describe reverse osmosis water is filtered. Distilled water has been boiled and the condensation has been captured then turned back into the water. Uses For Distilled Water vs. Reverse Osmosis Water Still confused? Things become a lot clearer when you consider what water commercially produced using either method is typically used for. Bottles of distilled water are typically used for applications in which minerals would be an obstacle. You see, the water supply of most municipalities contains plenty of minerals. These minerals can adversely affect things like steam irons and indoor aquariums. Certain laboratory experiments also require distilled water. Reverse osmosis water is primarily used for drinking. Difference Between Reverse Osmosis and Distilled Water In Your Home Residential water distillers do exist but they use a lot of energy and are much less common than reverse osmosis filters. With a reverse osmosis filter, getting pure water is as simple as opening your faucet. The process runs without much input from you, whereas the distillation process is much more involved. Again, it’s not as simple as boiling the water and calling it a day as many people mistakenly believe. Distillation also typically produces quantities of water far less than what most people need. For this reason, at American Home Water and Air, we carry and service reverse osmosis systems. It’s much more practical. More About Minerals Earlier, we mentioned that both reverse osmosis and distillation remove minerals from water. This leads to a common misconception. We covered it in great detail here but it’s also worth a brief exploration in this post. High concentrations of minerals in water are not bad for your health but they do damage your plumbing and appliances. The reason steam iron manufacturers typically recommend that you use distilled water is that the minerals in straight tap water will build up inside the iron, causing clogs and other concerns. This also happens in pipes, showerheads, and dishwashers. While the difference between reverse osmosis and distilled water is slim when it comes to mineral removal, neither process is efficient for every application you’d want mineral-free water for. You wouldn’t, for example, connect a reverse osmosis system to your showerhead. Likewise, you wouldn’t use a water distiller to produce shower water. Either of these processes would be inefficient. What you’d want instead is a water softener. These systems offer many benefits, the most impressive of which is their capability to produce enough soft water for your entire house. Water softeners in Phoenix are especially key since the area is known for its mineral-rich water supply. Many residents use these systems alongside a reverse osmosis filter. The water softener removes minerals while the reverse osmosis filter takes care of contaminants and chemicals. Is Reverse Osmosis Water The Same As Distilled Water? Conclusion In this post, we explored in great detail the topic of distilled water vs reverse osmosis water. To recap, both processes do purify water. Distillation, however, is energy-intensive and involves capturing the condensation of boiling water. Reverse osmosis, on the other hand, forces your water through a series of fine membranes to remove particles and chemicals. Reverse osmosis is a much more practical solution for most consumers since it produces a greater amount of water more reliably. Accessing that water is as simple as opening your faucet. Now that you know the difference between reverse osmosis and distillation, feel free to give us a call at American Home Water and Air for all your water filtration needs! If you’re looking for more information about the types of water you can consume and water quality, you can check out our article about deionized water. Found this helpful? Check out Hot

6 Key Benefits Of Reverse Osmosis Water

Benefits Of Reverse Osmosis

Among the various types of water filtration systems, reverse osmosis tends to be the most popular. In this post, we’ll explore the various reverse osmosis water benefits to help you understand why that is. We’ll also fill you in on any potential downsides to reverse osmosis water. Our exploration of these two angles will help you decide whether a reverse osmosis filter is right for your family. Reverse Osmosis Water Benefits #1. RO is Highly Effective at Removing Contaminants When discussing reverse osmosis benefits, it makes sense to point out that they do their job (filtering drinking water) very well. The method is used at virtually every scale, from large (i.e. treating wastewater) to small (i.e. filtering water in your home). Our reverse osmosis systems in Phoenix rely on four to five stages of filtration. This filtration includes progressively finer membranes that remove contaminants from your water. These contaminants include: Reverse osmosis can remove as much as 98% of these contaminants from your drinking water. This is much more effective than using a charcoal filter alone, which is incapable of removing certain contaminants. #2. RO is Energy Efficient, Too Given how powerful and effective reverse osmosis systems are, you might be surprised to learn that they actually don’t use electricity. This stands in stark contrast to something like distillation, which requires heat and therefore electricity. A reverse osmosis system benefits from the water pressure in your home. That’s all it needs! #3. RO Provides Clean Water On Demand Another downside of distillation is that it requires considerable input from the user. You’ll always be conscious of the process since you need to refill the tank in order to keep up with your household’s water needs. One of the benefits of a reverse osmosis filter is that it connects directly to your faucet, providing clean drinking water on demand. Over time, you may even forget the filter is there, doing its thing. #4. RO Also Removes Minerals Water filters cannot totally replace softeners (read more about that here). On a residential level, reverse osmosis filters are most often intended to provide clean drinking water, as opposed to water for your shower as well. Nonetheless, reverse osmosis does remove many of the minerals that produce hard water. Hard water, in turn, causes scale and other issues. So if you’re unable to afford a water filter and a softener in one go, one option is to install a reverse osmosis system that will at least protect your kitchen faucet until you’re ready to install a softener as well. Better yet, you can also opt to install a water softener with reverse osmosis. Note that (as we mentioned in this detailed article about demineralizing water) relying on a reverse osmosis system to filter minerals will reduce the filter’s lifespan. #5. RO Will Save You Money Another example of the key reverse osmosis system benefits is their ability to reduce your living costs drastically. If you’re used to buying bottled water, you’ll be pleasantly surprised at how much cheaper it is to simply filter your home’s water supply. Depending on how much water you use, these savings can range from hundreds of dollars to thousands per year. #6. RO Results In Better-Tasting Food Because reverse osmosis systems remove minerals and impurities, many people report better-tasting food. The minerals and chemicals in untreated water can actually alter your food’s taste when you use that water to cook. While boiling kills bacteria in the water, other contaminants stay put. Disadvantages of Reverse Osmosis At American Home Water and Air, we believe in transparency. Although we sell reverse osmosis systems, we like to be very open and upfront about potential limitations. Just keep in mind that the reverse osmosis benefits we mentioned above outweigh any downsides for most homeowners. #1. You May Need To Get Used To The Taste One of the biggest disadvantages of reverse osmosis is that you may not like the taste immediately. Because reverse osmosis removes many of the minerals you’re likely accustomed to in water, it can taste “flat” or unusual. Note that there’s a common misconception concerning the RO process’ removal of minerals. Many people think that these minerals in water are actually crucial for peak health. In reality, your body gets most of its supply of these minerals from your food. You’ll be just fine without them in your water. #2. RO Does Require Some Maintenance For the most part, as we mentioned earlier, the benefits of a reverse osmosis filter include a largely carefree operation. However, you still need to perform some simple maintenance by way of filter replacements in order to avoid disruption. Thankfully, you only really need to do this about once per year. #3. Depending On Your Water Usage, You May Have To Wait For Filtration For most households, reverse osmosis systems are capable of producing enough water on a daily basis. If you use a lot of water at once, you may need to wait for the system to build up enough water again before you can use it. To get around this, you can install a separate spigot to limit the amount of reverse osmosis water you use. We offer this free of charge to our clients in the Phoenix area. If you’re not located in Arizona, look for a service company in your area that does the same. Conclusion If you’re looking for the absolute best in water filtration for your household, a reverse osmosis system is for you. There’s a reason these systems have become so popular all over the country. To recap the benefits we’ve discussed, reverse osmosis is highly effective at removing contaminants. It’s also energy-efficient, produces water on-demand, removes minerals, saves you money, and makes your cooked food taste better. The downsides are very minimal, including an unusual taste that you’ll warm up to in no time. If you’re in the Phoenix, Arizona area, give us a call to find out about our reverse osmosis system services. We provide,

Lead Water Filter: Is A Whole House System Effective?

lead water filter

If you’re shopping for a lead water filter, whole house systems will eventually pop up on your radar. But are they really effective at removing lead from your drinking water? What’s this highly toxic compound doing in your water, anyway? Today, we’ll answer these questions and more to help you ensure safe drinking water for yourself and your family. Is The Water In Phoenix Safe To Drink? It’s no secret that tap water all throughout America is of poor quality. Research has shown that millions of Americans drink water containing elevated levels of bacteria and even lead. Phoenix, Arizona is no exception to this rule. In fact, recent reports have indicated that dozens of schools in the area receive water contaminated with lead. This, combined with the government’s apathetic response, is why reverse osmosis systems in Phoenix are so popular. But How Does Lead Get Into Our Water Anyway? Underwater pipes are one of the most common sources of lead in drinking water. Officials in Phoenix are instructed to replace these pipes upon encountering them but many still remain connected to the infrastructure that serves our homes and schools. How Can I Test For Lead In My Water? The Environmental Protection Agency maintains a database of experts in each state that will conduct testing on your water for free. Visit their website here and contact a laboratory in your state for more information. What’s The Big Deal About Lead In Water, Anyway? Given the government’s apathetic response, less skeptical folks might also shrug and assume the effects aren’t really that bad. At American Home Water and Air, “not that bad” isn’t good enough for our families — and we don’t think it should be for you either. While the levels of lead in drinking water throughout America aren’t always high enough to cause immediate negative effects, the damage occurs over the long haul. According to the World Health Organization (WHO), lead is a “cumulative toxicant.” Your body stores it in your teeth and bones. There, it accumulates and unleashes effects over the long haul. These effects are so dire that the WHO predicts lead exposure robs humans worldwide of 24.4 million years of healthy lives. That’s nothing to balk at — especially when solutions like reverse osmosis filters are so easy to have installed. Lead Water Filter: Do Whole House Systems Work? A whole house lead water filter can be very effective at removing not just this toxic compound from your water but plenty of others as well. They’re so effective, in fact, that part of authorities’ response to the Flint Water Crisis involved giving them to residents. A whole house water filter for lead can come in a variety of forms. Let’s take a look at the most common ones and evaluate their effectiveness. Activated Carbon Filters Activated carbon filters soak up contaminants like: While a carbon-based whole house water filter for lead is effective at removing these chemicals, it is not as efficient in dealing with minerals and inorganic materials that have been dissolved. Reverse Osmosis Filters Instead of being a whole house lead water filter, most reverse osmosis systems treat water that flows through a single faucet. Whole-house systems do exist, however. Reverse osmosis isn’t as effective at removing other types of pesticides, however. This is because pesticide molecules are much smaller than water molecules. The membranes in reverse osmosis systems cannot stop them from passing through. The reverse osmosis systems we provide at American Home Water and Air overcome this by using several stages of membranes. These progressively-finer membranes rid your water of virtually all contaminants. Combination Filters Another common type of whole house water filter for lead removal is one that relies on multiple types of filters, including carbon. Filters such as our Pro-Health System will not only purify your water but soften and balance its pH levels as well. Which Filter Is Best For Removing Lead? All of the systems we mentioned will adequately remove lead from your drinking water. Which one is right for you depends on a variety of factors, including your home’s existing filtration infrastructure and your family’s water needs. If you’re in the Phoenix, Arizona metro area, we invite you to contact us at American Home Water and Air. We’d be happy to look at your situation and not just recommend a filter but also explain why we believe our recommendation is the best choice for you. Frequently Asked Questions Can you filter out lead from water? You absolutely can. There are a variety of filters that do this, including reverse osmosis and carbon filtration. Do Brita filters filter out lead? Brita filters do remove lead. However, if you are contemplating using one of their smaller, single-fixture filters you may find yourself better off using a whole-house system. Are whole house water filters worth it? At American Home Water and Air, we want the safest, best-quality drinking water for our families. While a good whole house water filter will certainly cost you, we like to think that the benefits (namely, safe drinking water for your family) make it priceless. Does a fridge filter remove lead? The specialized filters required to remove lead are rare in refrigerators. A whole-house system can filter your water before it even reaches your fridge. Does boiling water remove lead? Boiling water will not remove lead from it, according to the CDC. In fact, boiling water contaminated with lead can even increase the metal’s concentration. This underscores the importance of an adequate filtration system; even cooking with water will not get rid of heavy metals like lead. Can lead be absorbed through the skin? Lead won’t seep into your skin through water, meaning bathing in lead-contaminated water in and of itself won’t harm you. The issue is with water that you ingest. Note that children sometimes drink water from the showerhead.